SELLEYS Liquid Nails Upgraded Formula

By /

‹ Adhesive

SELLEYS Liquid Nails Upgraded Formula

SELLEYS Liquid Nails is a premium grade, solvent based, synthetic rubber multipurpose construction adhesive that delivers a consistently STRONG and LASTING BOND on most building substrates. Its formaldehyde content in accordance with national standards, and also complies with Hong Kong VOC regulations for multipurpose construction adhesives (VOC < 70g/L). High strength, loading 34.5kg/c㎡ Multipurpose All weather

Dealers
eShop

TDS

MSDS

Test Report

Features

Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last.
Excellent resistance to water and weather makes it suitable for interior and exterior applications.
Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures.
Adheres well to wet and dry timber, so there is no need to wait for the timber to dry.
Fast grab and rapid cure.
Resistant (after full cure) to heat to 90℃ and cold to -10℃. See “Handy tips” below.
Doesn’t drip, sag or string.
Bridges gap up to 9mm hence can be used on rough and ill-fitting construction materials.
Paintable when dry, to give you a neat, quality finished job.

Available Sizes
360g cartridge

Colours
Brown
White

Volatile Organic Compounds (VOC) Content
< 70g / L # Formaldehyde content in accordance with national standards “GB18583-2008 Indoor decorating and refurbishing materials - Limit of harmful substances of adhesives”

Information

Where can this product be used?
Timber panels to walls and frames
Bonding timber

Perfect for use
Sheet flooring to joists
Metal or aluminium door strips to floors or walls
Timber or fibre cement sheeting to cement block or brick walls
Masonite / hardboard to timber or floor boards
Wallboard or panelling to wood or metal frames
Cork tiles to timber, fibro or plaster
In the groove of tongue and groove flooring as it is installed to avoid later squeaking

What materials is this product suitable for?
Timber
Plasterboard
Medium-density fibreboard (MDF)
Particleboard
Masonry
Concrete
Tiles & Ceramics
Metals
Most plastics*
Rubber
Glass
Many other building surfaces
* Pre-test to determine compatibility

How To Use

How to use this product
Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials.
Cut the tip of the cartridge and pierce foil seal inside. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun.

CONTACT BOND METHOD (For dry, porous and lightweight materials)
Apply a ‘zig zag’ bead of adhesive to one surface only, apply beads every 40cm. press together and pull apart. Allow surfaces to dry a few minutes before firmly joining.

WET BOND METHOD (Use with clamping, for heavy materials)
Apply a ‘zig zag’ bead of adhesive, assemble joint within 10 minutes using sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Allow adhesives to set (at least 24 hours) before removing any temporary fasteners or clamping.

Clean Up
Wet adhesive – Clean off with mineral turps
Dry adhesive – can be removed by scraping or sanding

Handy tips
The product is repositionable for up to 20 minutes after fitting.
The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days.
Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (eg metals and dense timbers).
Take care to prevent spills of adhesive onto lacquered timber surfaces, as solvents in the product may damage the appearance/finish. Or you may use SELLEYS Liquid Nails Fast to prevent it happens.
Should not be applied at temperatures below -5℃.
Not recommended for tightly clamped joints; eg cabinet making or joinery.
SELLEYS Liquid Nails Fast is preferred for styrene foam.
Not suitable for use on mirrors.
Bonds weaken at high temperatures (eg above 50°C). Avoid bonding metals or heavy materials which will be heated by direct sun, eg to metal roofing and siding.

Safety tips
Keep away from children.
Avoid contact with skin & eyes.
If in eyes, rinse immediately with plenty of water and seek medical advice.
If contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
If swallowed, do NOT induce vomiting and seek medical advice..
Ensure you use a well ventilated area
Highly flammable. Vapours can be ignited by flames or sparks.
Avoid contamination of waterways. Allow waste or left over product to completely dry out before disposing of it.
Refer to Material Safety Data Sheet for more information.

Storage
Store in a cool place away from sources of ignition and as required by regulations for storage of low flash point flammable liquids.
The adhesive should be used within 6 months after opening.
After use keep the nozzle on the cartridge. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent evaporation for longer storage.